General discussion • Re: Knob to pot shaft dimesions
Actually the shaft length is 15mm, the recess is 11mm, you might have to cut some off for that knob. But it depends where the flat ends on the shaft and in the knob.The pot also has diagrams as well...
View ArticleCompute Module • Re: USB-MSD Boot with CM5 using custom board
CM5 only supports USB-MSD boot from the RP1 XHCI controllers.Statistics: Posted by timg236 — Mon Jan 27, 2025 10:58 pm
View ArticleBeginners • Re: Pi 5 power options?
I'm sure OP will be back soon to participate in the discussion. It was obviously important enough to create an account and bring up the subject.Statistics: Posted by ame — Mon Jan 27, 2025 11:04 pm
View ArticleCamera board • Video captured can't be shown!
I use a Raspberry Pi 5 with a Pi Camera V2 and a Pi Camera V3. I can use both camera to capture pictures and previews. But, when I used rpicam-vid to record video, the video file can't be played back...
View ArticleBeginners • Re: ino files from my windows system to the raspberry pi 4b
My Windows Arduino INO files are in C:\Users\dl1im\OneDrive\Documents\Arduino each one is in a seperate folder under there.Statistics: Posted by DougieLawson — Mon Jan 27, 2025 11:31 pm
View ArticleCamera board • Re: rpicamsrc support in Bookworm
rpicamsrc is for the legacy camera stack which is deprecated.viewtopic.php?t=362707Would you suggest to use to achieve my goal? I need to use gstreamer and control shutter speed in the runtime.I tried...
View ArticleAdvanced users • Re: Automatically Enabling Raspberry Pi 4 Cores Based on...
leave them onplay with arm_freq= & arm_freq_min= insteaddo lscpu to see the stock numbersexample:in /boot/firmware/config.txtarm_freq=1000arm_freq_min=300honestly though the savings is not really...
View ArticleGaming • Re: QuakeSpasm 0.96.3 - Quake Source Port
quakespasm/Quake/bni is correct, and to load Blood + Iron, start QuakeSpasm, and enter game bni in the console.Statistics: Posted by Moonmarch — Tue Jan 28, 2025 1:13 am
View ArticleTroubleshooting • Any way to reset WiFi after bookworm with SD?
I have a headless pi zero w, I need to change the WiFi don't currently have access to HDMI mini or ssh is it possible to change with SD card access? I searched and apparently you can no longer use...
View ArticleGeneral discussion • Alternate Power Supply
I'm getting rather frustrated with the Pi 5 and it's power issues. I've purchased the genuine Pi 5 power supply and I'm still getting the error message on screen, not every time but quite frequently....
View ArticleBeginners • Re: Need info on monitors
Thank you both!RoyStatistics: Posted by rtroxel — Wed Jan 29, 2025 12:11 am
View ArticleNetworking and servers • Re: Pi homelab build...
No disrespect whatsoever to Debian, but for my purposes, I would actually be better off if Rocky Linux would be ported to the Raspberry Pi 4 and 5... Trying to catch up and keep up with things that...
View ArticleGeneral discussion • Re: Replacement for the VL805
Renesas μPD720201/2 seems to be the chip used in many Chinese USB internal PC hubs. But I doubt there is any software support for it for a CM4 so you'll have to write that...
View ArticleGeneral discussion • Re: RPI USB3 Hub question
Regard a PD handshake in the hub, is there an hub IC that does this ? Might be the issue.If the PMIC on a Pi5 can do it, there should be something even less complex that just does the PD handshake and...
View ArticlePython • Re: Rasp pi Pico wont work once soldered to headers
So, let's dissect this because your problem may not have anything to do with solderingSetting up pico and went through the setup on thonny, got the onboard led to turn on etc. Soldered half the header...
View ArticleAdvanced users • Re: GPIO Sampling Speed With Kernel Driver
With bare metal you can get 75MBps continuous. But it you're using an OS then maybe something less.Statistics: Posted by MikeDB — Wed Jan 29, 2025 12:57 am
View ArticleCompute Module • Re: CM5 IO board reboot & shutdown hang when booting...
Is anyone able to reproduce this behavior? It should be fairly straightforward, this is all official unmodified hardware & software.Statistics: Posted by Muny — Wed Jan 29, 2025 1:13 am
View ArticleTroubleshooting • Re: Connecting to pi using hostname/local address always...
SurferTim wrote: Easy. Disable one, then the other. Test 1: Enable wifi.Pull the ethernet cable out of the RPi. Test 2: Disable wifi.Insert the ethernet cable into the RPi. Ah I see what you mean, and...
View ArticleNetworking and servers • Re: kiwix offline website browsing (eg. Wikipedia),...
> "Just use the version in the repos. "kiwix-desktop, as installable by apt, wouldn't show/refresh the available ZIMs, as downloadable online. The version is also out of date. As to flatpak, I like...
View ArticleTroubleshooting • Re: Raspberry Pi 4 Model B (2 GB) Ethernet Port Issue –...
Are your cables going all the way in to the click-lock stage? A couple of my Pi4's need a bit of manipulation and force to get them all the way in.Have you done a good inspection of the ethernet...
View Article